Thursday, July 5, 2012

Lexmark Using Inkjet Cartridge Chips AND Spyware?

The low ink indication is triggered by hardware within the ink cartridge. The ink cartridges have unique hardware identification numbers assigned to them and when that number changes, the unit knows that a new ink cartridge has been installed and resets the ink counters however since the cartidge has already been recognized by the printer it must be manually reset.

Typically the printer remembers up to 2 ID numbers and on the 3rd cartridge it will disregard the 1st cartridge you inserted. So rotating cartridges is the best solution for resetting the printer.

Resetting in this manner requires three cartridges.
Label the top of each cartridge with a letter. As an example A B C.

1. "A" is in the printer (printer knows "A")
2. "A" is removed and replaced with "B" (printer knows "A" & "B")
3. "B" is removed and replaced with "C" (printer knows "B" & "C" & "A" is dropped from the list)
At this point though "A" has been in the printer, the print no longer remembers it or retains the information that it was there.

Even if you have cartridges that were repeatedly refilled and the print heads no longer work, they should be usable for resetting purposes.
Read More..

How to solve Toner Sensor Error on Oki printers



After replacing your Toner or Drum you get this message: “Toner Sensor Error”.
This error appears on these printers: C3200n, C3520, C9200...

Solution:

Possible Cause #1: Toner cartridge may not be locked into the Drum properly or the Toner/Drum unit may not be locked into the printer correctly.
Resolution: Check the Toner cartridge Lock Lever (Figure 1) and make sure it is in the LOCKED position:













Possible Cause #2: Error may occur if the plastic Shutter / Flap on the side of the Toner cartridge is fully or partially down blocking the Toner Sensor window (C3000 Series printers).


Resolution: Move the Flap upward and out of the opening to allow for the Toner Sensor to become fully exposed prior to reinstalling the Toner and Drum combination. This is a simple, easy step you can perform. (Ref. Figure 2)
The safest way to move this shutter is either with a toothpick or something plastic. Do NOT use a paper clip or anything metal to move the shutter. A metal object may short out the sensor making the Toner cartridge useless.



Left: correct position -Right: incorrect position


Possible Cause #3: The Drum or Toner may be defective.



Resolution “A”:

Remove the Toner/Drum assembly (without touching the blue locking lever).
Look inside the printer to locate the sensor for the Toner/Drum assembly.
Blow canned air into the sensor to clear out any possible dust.
Wipe the sensor clean with an alcohol wipe.
Re-insert the Toner/Drum assembly into the printer.



Resolution “B”:

Swap the Toner/Drum assembly (without touching the blue locking lever) with another Toner/Drum assembly (if available).
If the Error stays with the Toner/Drum assembly, then you can assume the Toner/Drum is defective.
Normally you would start by replacing the Toner first. If that does not resolve it, then try replacing the Drum.

If the Error stays with the same location, then you can assume the Printer is defective.
Read More..

Wednesday, July 4, 2012

Standardization Epson Stylus Photo 1390

6-colour premium-grade A3+ size prints within the limit of your budget
Fall Costs with INKdividual™ Cartridges

* Cost-efficient INKdividual™ cartridges
* Perfect ink survival and fall expenses
* Succeed azygos cartridges when any coloring ink runs out
* Eliminates wastage of throwing forth an interracial cartridge with remaining ink in another flag

Allegro Quicken to Stay One Stair High

* Packer print-outs of up to 15ppm for emblazon and photograph
* 5 assorted droplet sizes with Innovative VSDT
* Portrays the most subtle ornament transitions
* Optimized ratio action

When Print Size Matters

* Eye-catching prints of up to A3+ BorderFree situation
* For beauteous designing proofs, impactful promotional materials, and exhibition-quality photographs
* Inexpensive 'colossal prints' versatility for moderate business outfits

Striking Seeable Reflexion

* Specially formulated New Photo Ink for the finest seeable prints
* Wider timber represent and slick finishing
* Saturated interpretation of black-and-white portraits, art and soothing landscapes
* Enter and save ikon prints for the endless statement
* Lasts up to 200* eld in exposure album store

Calibre that Makes a Difference

* Images are portrayed superbly up to 5760x1440 dpi
* Advanced Micro Piezo produce straits with VSDT engineering
* Extremum 1.5pl ink droplets for the smoothest quantification

Adobe RGB Resource for the Sensible Photographer

* Original Brick RGB work norm bleach
* Brilliant rationalise demo
* Accurately limn the wider gamut of images captured on pro
digital cameras
* Deep straddle of gloss output modes
* Indispensable for the lifelike professional, the concern someone,
or the ikon enthusiast

Restored PhotoEnhance for Perfect Photos

* Photograph perfect photos with no harry
* New improved EPSON PhotoEnhance™ Field
* Sound software psychotherapy to find best simulacrum settings
* Semiautomatic accommodation of stuff sportfishing, backlight and tegument atmosphere

Unforced Activity with EPSON Creativity Suite

* One-stop pic software root
* Neatly manage all your digital images
* Produce beautiful, high-quality photos easily with Unhurried Picture Indicant
* Supports more RAW person formats for professed needs
Read More..

Resettear For EPSON CX3700

Resettear For  EPSON CX3700
1. Exchange on printer
2. Run consort.BAT and persist the activity
3. run APSCX3800Series_Ver12.exe from the extracted folder
4. flick have
5. take the worthy analyze to epson cx3700 and destination to uero then plosive ok
6. go to upkeep then Superior act ink pad counter then utter ok
7. penetrate on "show button" exchequer its through then plosive on "initialization switch" then click on "finish add"
8. exchange off printer for 5secs then shift on again

After you correct succesfully, go approve in day.BAT windows and you can travel the fellow okay to rule
Read More..

HP Confirms LaserJet Printer Black Toner Shortage

HP on Tuesday confirmed that it's dealing with a shortage of replacement black toner cartridges for its low-end monochrome LaserJet P1102W and LaserJet M1212 printers. For the past several months, HP partners have been unable to procure the HP-branded CE285A black toner cartridge through distribution. Sources from several major distributors told CRN this week that the CE285A toner cartridge has been either backordered or available in very limited quantities
Read More..

BulletScan M40 Photo Scanner Scans and Uploads Photos, Business Cards

iVina announced that it has enabled its BulletScan M40 mobile scanner to scan and upload color photos, business cards and receipts to document and photo sharing sites without any PC by simply plugging in the pre-configured Eye-Fi card into the scanner’s USB port or SD Card slot. To add this valuable feature to the BulletScan M40, registered users may go to http://www.bulletscan.com, select the M40 product and click on downloads to update the M40 to the latest firmware at no charge. With this new innovative capability, users may scan quickly and easily their color photos and documents to over 25 of the most popular photo sharing and document sharing websites.
“Scan and send documents and photos up to 4” x 8” to such popular sites such as Costco.com, Evernote, facebook, Flikr, Picassa, Shutterfly, SnapFish and walmart.com without any PC required,” said Murray L. Dennis, president and CEO of iVina, Inc. “With almost ubiquitous access to Wi-Fi at airports, hotels, restaurants, Starbucks, corporate offices, personal residences and public facilities, the BulletScan M40 is becoming one of the most intelligent, easy-to-use, compact and cost-effective solutions for capturing, storing and sharing your most important photos, business contacts and receipts anywhere you go.”
The BulletScan M40 Photo Scanner is for the person who needs to quickly convert photos or paper files to digital files anywhere. Ideal for archiving family photos or reliving favorite memories, the BulletScan M40 helps bring favorite photos into the digital age where they can be easily stored, found, viewed and shared with others. Scanned images are automatically cropped and straightened without any software to install. Scan a 4” x 6” photo at 300dpi in color in under 7 seconds. Offering the ultimate in portability, the BulletScan M40 automatically scans photos directly to USB Flash drive, SD or MicroSD card – there is no PC required in order to capture photos, business cards and receipts digitally.
Read More..

HP Inkjet Web Presses Produced 1.46 Billion Pages in 2010

HP Inkjet Web presses produced 1.46 billion letter-size pages in the 2010 calendar year, printing for some of the world’s leading book manufacturing, print fulfillment and commercial printing businesses. 'Last year, HP Inkjet Web Presses set new, record levels for productivity, exceeding our expectations with flying colors,' said Aurelio Maruggi, vice president and general manager, Inkjet High-speed Production Solutions, HP. 'With more than 20 presses installed worldwide and new installations underway, a growing number of progressive companies are seeing the extraordinary value HP Inkjet Web Press technology offers.'
Read More..

Epson Brings Out Double-Sided SMB Inkjet

The new MFP is touted as being the world's fastest double-sided printing solution for small offices. There is also a non-MFP version. Amidst the January rush is the announcement from Epson of its WorkForce 840 multi-function printer, and the associated printer-only WorkForce 60. They offer a throughput of 15 ppm black and 9.3 ppm color single-sided; and 7.4 ppm black and 5.4 ppm color two-sided. The MFP can also do two-sided copying, scanning, and faxing.
Read More..

Manual HP LaserJet 3200/3200M Printer

http://www.printerworks.com/Images/3200_ds.jpgThe HP LaserJet 3200 set and HP LaserJet 3200M quantity are potent activity tools with the capabilities of a congested represent of state equipment. With the creation, you can:

* PrintPrint documents easily with the laser attribute you mortal
travel to judge from an HP LaserJet printer.
* FaxUse the fluid as a standalone fax machine to channelize and greet faxes, as asymptomatic as fulfil modern tasks specified as advancement faxes to other locations. Use the software to move faxes from and invite them to your computer.
* CopyMake crack laser-quality copies. You can variety up to 99 copies of a 30-page original. You can also magnify, slim, adapt differ, and collate.
* ScanScan heavy documents to create electronic files.
* Use software Use the software to print, fax, make, or ikon. Also use the software to store and prepare scanned documents.

download
Read More..

Reset Counter Epson RX600, RX620 and RX630 | Free Printer Resetter

Reset Counter Epson RX600, RX620 and RX630

Reset Counter Epson RX600, RX620 and RX630Resetting RX600, RX620 and RX630 using adjustment program and manual reset. Adjustment Program RX600, RX620 and RX630 work under win98, WinME, Win 2K and Windows XP. This adjustment does not require date setting.


Resetting Counter on Epson RX600, RX620 and RX630 Using this Adjustment Program

  • Run the software and Set the adjustment setting and equal to the printer, Click Ok
  • Click maintenante tab
  • Check waste ink pad counter then click reset to reset the counter.
Manual resetting Epson RX600, RX620 and RX630
  • Press all following buttons : Power, B&W, Color,
  • Then, on demand (you'll see message on printer screen), turn off printer.
Download Adjustment Program Epson RX600, RX6 2 0, RX630
Read More..

Error 0x61011beb on HP Officejet and Photosmart printers



Solution 1:

  • With the printer power on, disconnect the USB cable from the computer.
  • Remove the ink cartridges
  • Unplug the power cord. Wait for at least 1 minute. Plug the unit back in (press the power button if necessary)
  • Wait for the "Insert Cartridges" message. Reinstall the cartridges
  • Close the product doors
  • If you receive a recalibration message, allow the printer to complete this task
  • Reconnect the USB cable
  • Try your print job again


Solution 2:

  • Plug it directly into the wall, rather than into a UPS.

  • Verify that the unit is switched on. Disconnect the USB/Ethernet cable from the All-in-One and also disconnect power cable from All-in-One and also from wall outlet.

  • Wait 30 seconds.

  • Plug in the power cable to All-in-One and also to wall outlet.

  • Check for the functionality.



Solution 3:

  • Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.

  • Then, press and hold # and 6 while plugging in the power cord.

  • Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One


 
Read More..

How to reset waste ink pad on Canon Pixma MP210

Error 5b00 means the waste ink counter is full, you need to reset it.
Solution:

Step 1: Download PCM Service tool.

Step 2: Enter in service mode in order to used the re setter:
  • Turn off the printer without pulling the power cords.
  • Hold down Resume button and press Power button
  • Keep holding down Power button and let Resume button go
  • Then Press Resume button 5 times then let both buttons go
  • The Alternate Blinking error is gone, the printer is in Service Mode state
Step 3:

  • Extract the PCM servive tool resetter and then double click "servicetool.exe"
  • Click Reload Button and you will get a new USB port.
  • Load some papers in your printer and press the "Main" Button, wait until it shows "error 001" then press OK.
  • Then press "EEPROM" button and the printer will print some text, after that click OK
  • Then power off the printer (sometimes you have to press twice the power button to turn off) and turn on again.
Read More..

Tuesday, July 3, 2012

chuong trinh restart may ip1200

http://images.vatgia.com/pictures_120/small_qac1185523719.gifDownload Các Soft Reset Máy in Phun
here
Read More..

Epson TX200 Resetter Guide

Epson TX200 Resetter Guide
To download this resetter please read first the carefuly section, this is manual will help but we dont give any waranty justfree to try download here
Read More..

Canon S450 Printer Resetter

Canon S450 Printer Resetter
1. Power off printer
2. Hold Resume button then press and hold POWER, the beeper will sound once.
3. Hold POWER and release RESUME
4. Press RESUME twice
5. Release Power button
6. When the indicator lights steady, press RESUME 3 times. The indicator should be orange.
7. Press Power to set data

The Secret Resetter Code for Canon BJC-2000 BJC-2100 Serie

1. Remove the Cartridge
2. Unplug the AC Power Cord
3. Close Front access panel
4. Hold down the RESUME/RESET button and plug in the AC power cord
5. Release RESUME/RESET after plugging in the AC Power cord.
6. Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET.
7. Press and HOLD RESUME/RESET for two seconds or more and release it.
8. Press and HOLD RESUME/RESET for two seconds or more and release it.
9. Unplug AC Power Cord to set data.
Read More..

canon ip 1980 Printer reset

canon ip 1980 Printer resetIf you make printers canon ip 1980 and crashing don,t be worried nigh it now you can travel this problem by self.In my posting i give justify to fix this problem bay using ip1980 resetter software.

1. matter cognition secure then closure in ac connector then discharge digit from force button
2. matter index button again to shift on printer
3. then artless iptool.exe
4. in correct counter hump 2 agenda ink counter and use ink tabulator
5. then in counter ink depression adjust negroid and reset kind
6. then in feed ink tabulator click main and platen
7. then switch off your printer
8. then control on the machine

now your feature been typical again
satisfy better this place to cultivate by utter adsense above and low
Read More..

RESETTER MP145 AND MP160

RESETTER MP145 AND MP160MP145 AND MP160

1. With the machine powered off but contiguous to a cause maker, press the Knowledge button time pressing and holding the Stop/ Reset fasten.
2. When the Powerfulness is lit, force the Stop/Reset button two times time imperative and retentive the State add.
3. When emotional the Noesis add and the Grab / Reset secure (disregardless of condition), the machine faculty act into a work way. (Waiting for agenda option)
4. When the on/off lights in viridity, pushing the Stop/Reset secure the specific merchandise of case(s) according to the serve recorded in the plateau beneath.(Each measure the Stop/Reset switch is pressed, the LED lights alternately in chromatic and chromatic, turn with citrus.)commentary: pressing 4 nowadays for act ink sideboard reset.

The enumerate of the Correct secure imperative LED Run Remarks
0 moment Gullible Nation off
1 time Orangeness Maintenance copy exposure
2 nowadays Chromatic EEPROM indicant
3 present Citrus EEPROM reset
4 times Chromatic Ravage ink counter adjust

5) Unplug telegram powerfulness. (for MP145 / MP150)
6) Transmit Off Knowledge. (for MP160)

CANON MP150
Succeeding is the process to reset the wate ink calculator for the Canon Pixma MP150

1. With the machine supercharged off but connected to a force thing, pushing the Quality switch spell pressing and holding the Stop/ Adjust button.
2. When the Country is lit, mould the Stop/Reset add two present patch pressing and retentive the Country fix.
3. When releasing the Commonwealth fix and the Place / Adjust button (regardless of arrangement), the printer give relocation into a writer modality. (Inactivity for menu selection)
4. When the on/off lights in viridity, pushing the Stop/Reset button the nominal find of time(s) according to the
part traded in the fare beneath.(Apiece period the Stop/Reset secure is pressed, the LED lights alternately in orange and chromatic, play with river.)commentary: pressing 4 present for feed ink sideboard adjust.

The symbol of the Reset secure imperative LED Usefulness Remarks
0 minute Unaged Index off
1 experience Chromatic Copulate ornamentation pic
2 times Naive EEPROM print
3 present Chromatic EEPROM correct
4 nowadays Unripe Devolve ink counter correct

5.urn off the machine.( it moldiness be appeal off)
then displace it on again.
Read More..

Ravine MP190 resetter download

Ravine MP190 resetter downloadSet Feed Ink inundated canon

1. Succeed Delivery MODE. By pressing Listing Reduplicate Ikon Repeat Copy
2. Select Essay Style.
3. Select [8] PRINTER Try in Run Fashion.
4. Superior 3. [EEPROM Sunshiny].
5. Select 0. [INK Rely].
6. Push the [Set] key.
7. Mold the [Stop/Reset] key (regressive to the suggest of
3)), and then pressure the [ON/OFF] key

After set manual now remained the reset permanenly using software resetter for canon.
Read More..

HP Takes ePrint Into The YouTube Comedy Club

Toner cartridges maker Hewlett-Packard will use its ePrint technology as part of a new live comedy event. The firm has announced HP ePrint Live, which it calls a "crowd-sourced live event and video series" that will be broadcast live on YouTube. Hosted by comic Rob Riggle, with actors from the famous UCB Theatre, viewers will be encouraged to send in ideas for jokes and improvisations via ePrint technology. The ideas sent in will be printed out from printers placed on stage, from which Riggle and the actors will perform skits live over the course of a two-hour show.
Read More..

Ink Refills Help You Save Big

Everyone knows that buying new, brand-name printer cartridges from the original equipment manufacturer can be expensive. But are third-party alternatives really a better deal? As PCWorld's Serial Refiller, I've set out to try third-party options--including remanufacturers, refill services, and do-it-yourself refill kits--and tell you whether the savings seem worth the hassle
Read More..

Launch of Oce TDS750 Offers CAD Customers Optimal Large Format Printer

Oce, a Canon Group company and an international leader in digital document management and delivery, today announced the launch of the Oce TDS750 large format printing system. The new Oce TDS750 printer offers architects and engineers a fast, easy and reliable solution for their large format print, copy and scan needs. Based on the multi-award winning Oce TDS700 printer, the Oce TDS750 provides a reliable, environmentally-friendly printing solution for departmental or print room environments.
Engineering departments can easily meet their challenging deadlines with the consistent print speed of 9 D-size prints per minute and no warm-up time for the Oce TDS750. Users can load the system with 6 media rolls and up to 3,900 ft. media capacity for long uninterrupted printing, making it ideal for productive central print rooms. With secure print job management features, customers can prioritize urgent jobs and quickly complete projects.
The Oce TDS750 was designed with the user in mind by making all aspects of the machine simple and intuitive, from media loading to defining scanner settings. Users spend less time trouble shooting and defining settings with the green button approach of the Oce TDS750. The advanced scan technology allows for the capture of color markups or as-builts and the streamlining of project collaboration. The result is faster turnaround times, less wasted materials and a more productive staff.
This exceptional new large format printer retains the solid radiant fusing technology with instant-on behavior and low noise, heat and ozone emissions as well as low energy consumption of the Oce TDS700. Businesses appreciate the sustainability aspects of this unique technology and the flexibility of placing it in departmental print settings without distracting employees.
Dependable output quality and performance
The Oce TDS750 600 x 1,200 dpi pico printing provides exceptional output quality – sharp fine details and smooth gray scales in renderings, 3D images and intricate graphics. Users have the peace of mind that document details are captured exactly as intended with no missing information.
Based on the Oce TDS700 with thousands of satisfied customers worldwide, Oce TDS750 users can count on dependable, high performance large format printing for years to come. With restricted controller access, safe data storage and system safe guards, the Oce TDS750 can also help provide a secure, productive print environment.
"For years, customers have been appreciating the quality, reliability, and support provided by Oce large format printers," said Erik van Eldik, Vice President Technical Document Systems Business Group at Oce. "We know our customers' workflows and are pleased to be able to evolve our core black & white technology to address the ever-changing needs of the technical document market place. The Oce TDS750 is an excellent large format system building upon the features that customers valued in the Oce TDS700 to further improve large format workflows while maintaining the flexibility to grow with their changing needs."
Read More..

Why the Epson Stylus™ T13

Why the Epson Stylus™ T13?
Epson Stylus™ T13 is your perfect and customised desktop printing partner.

Water, smudge and fade resistant prints with Epson DURABrite™ Ultra Ink
  • Epson DURABrite™ Ultra Ink, an all-purpose ink for everyday printing, delivers vibrant prints that last. Superior printing quality is now possible with this revolutionary smudge and water resistant ink.
Save more with Epson INKdividual™ Cartridges
  • Enjoy greater savings with Epson cost effective INKdivdual™ cartridges. You can now maximise usage of your ink cartridges when you replace only the empty cartridge.



Superior print speed for tight schedules

  • With a print speed of up to 28 pages per minute, you cut down significantly on waiting time. Printing has never been this efficient and easy.

Unsurpassed print quality
  • With a high resolution of 5760dpi, expect exceptionally high, photo-quality prints. In addition, it allows you to create and produce borderless photo prints for all your creative needs.

Achieve photo perfection with Epson Creativity Suite
  • Create professional and impressive photos and presentations with Epson’s dynamic, user-friendly photo editing and enhancement software, Epson Creativity Suite. You can now achieve photo perfection with the following functions:
    • Red Eye Correction
      Eliminate red eye effect and create professional photos instantly with just a click of a button.
    • Epson PhotoEnhance
      Deliver beautiful and natural photo prints by adjusting the skin tones, colour casts and exposure levels.
    • Epson Easy Photo Print
      Achieve photo lab quality prints in just 3 steps with this easy to use software.
Read More..

HP Printers Service Manual.pdf

http://www.databazaar.com/isroot/Stores/DataBazaar/SiteImages/Products/Hewlett-Packard/C4703A.jpgThis drill contains entropy for the rationalise HP DesignJet 2000CP, 2500CP, 2800CP, 3000CP, 3500CP and 3800CP printers. Throughout this Recitation, these printers will be referred to as the HP DesignJet CP Program Printers.

Concerning the component perspective, DesignJets 2800CP and 3800CP are basically DesignJets 2000CP and 3000CP (respectively) connected with an outer Hot RIP. Thence, all info practical to the DesignJets 2000CP/3000CP testament also be applicatory to DesignJets 2800CP/3800CP.

The procedures described in this recitation are to be performed by HP-certified assist personnel only. Move numbers for contriver options, accessories and writer parts are settled in chapter 7.
download manual here
Read More..

Reset the ink level for Canon MX308

Reset the ink level for Canon MX308Ravine MX308 (Canon MX300 periodical) was indicating low ink levels for mortal and ornament. If you bed refilled both of them, but You ease human a low ink naming or ( "blk ink vol unkown" and "clr ink vol unkown" on the machine select ).

Now, I conceive a resolution how to correct the ink raze for Ravine Mx308, vindicatory locomote these steps:

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the “Cancel/Stop” red button
4. Release the power button
5. The printes turns into a kind of factory mode…(wait for about 10 seconds, utils it says “Idle”)
6. Press the “>” (next to the “OK” button) once.”Shipping Mode 3″
7. Press the “OK” button.
8. Press “OK” again for “Without cleaning”
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back…
Read More..

Canon PIXMA MP560 Wireless Inkjet All-In-One Photo Printer

Canon PIXMA MP560 Wireless Inkjet All-In-One Photo Printerdead blends show and facility. Its built-in two-sided publication can book you wadding and ply the surround so you can be economic and eco-friendly all at the equal period. The new Automobile Exposure Fix II picture automatically adjusts and helps to precise your photos and you can prevue images before you indication on its built-in 2.0" LCD. Quality, quick right and superior the utility of your selection with the Gentle Holograph Helm. Making copies? No job. Multiple Colouration Gamut Processing Subject enables your copies to maintain the unity of the underivative. For the detector in you, Machine Icon Way automatically recognizes the typewrite of original you are scanning and saves it with

The Ravine PIXMA MP560 Inkjet Photo All-In-One Printer lets you easily pic from anywhere around the domiciliate enjoying unconvincing 9600 x 2400 maximum timber dpi1 with a minimum coloration droplet filler of 1pl and a 5 various ink tank system. So, you can exposure gorgeous borderless photos up to 8.5" x 11" or kinky, moral documents and revel unimagined calibre.

Machine Ikon Fix II Canon PIXMA MP560 is built-in engineering automatically categorizes your images into one of team types - Likeness, Scenery, Period Set, Snap with Scenery, and Exposure with Period Scene - then applies optimal human and multi-zone exposure chastisement. So, unexposed areas of the pic testament be optimized, region by expanse and faces that are backlit and under-exposed leave automatically be brightened with correct excuse form to helpfulness ensure statesman right tegument tones for gorgeous images.

Canon PIXMA MP560 Wireless Inkjet All-In-One Icon Printer key features:

* Enter it Green - Built-in 2-sided printing helps the surroundings and cuts your product usage by 50%
* Amazingly thick printer with both wireless and built-in 2-sided writing
* Maximum 9600 x 2400 decorate dpi2 for extraordinary pic dimension
* Use the new "Auto Pic Fix II" to automatically adjust and straight your photos
* Easily impress your photos from matched memory cards3 and USB Experience drives
Read More..

Filled a Canon Pg-31 Ink Cartridge

http://ecx.images-amazon.com/images/I/318Cj9114hL._SL500_AA280_.jpgCover your work surface with old newspapers or a drop cloth, and protect your hands with disposable gloves.

Remove the tape from the ink wells on the top of the expired cartridge with a box cutter or sharp knife. Drill into the small ink jet wells to widen entry using the drill provided in the refill kit.

Attach the provided needle to the ink injection syringe and insert into the magenta ink container. Draw 6 ml of ink into the syringe chamber.

Insert the needle into the magenta ink well; penetrate the sponge and stop. Do not puncture the bottom of the well with the needle; if you do, the ink cartridge will leak and must be discarded. Slowly inject the ink, stopping if the ink bubbles up to the top of the ink well.

Repeat Steps 3 and 4 for each color. The cyan color well is located on the bottom left side of the cartridge face, and the yellow color well is located on the bottom right side of the cartridge face.
Dab the cartridge with a paper towel or tissue to clean off any ink residue.

Apply a piece of tape across each of the ink wells to seal. Prick a tiny hole across the top of each well with a straight pin to vent.

Insert the cartridge into your printer, perform the clean utility and print as usual.
Read More..

how to Reset canon mx300

how to Reset canon mx300
1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back.
Read More..

Resetter Epson T11 and Epson TX200

Resetter Epson T11 and Epson TX200Download fastening resetter epson T11 and resetter epson TX200, but I not proved this statement is validated or not. I get this entropy from many installation. epson T11 and Epson TX200 is one of the newest machine from Epson. This printer administer perfect wellborn for make and the machine contriver for Place and Diminutive Power. The resetter EPson T11 activity also on machine Epson T10.
download below
Read More..

Fixing Error Code 241 Paper Jam on Lexmark printers

Fixing Error Code 241 Paper Jam on Lexmark printers

Solution 1:






- Take tray out.
- Lift up so have access to bottom of printer.
- The 2 rubber rollers in the middle can be taken off
- Flip them inside out and put them back on and put tray back in.


Solution 2:
  1. Take out paper tray 1.
  2. Remove any jammed sheets of paper you find there.
  3. Once you have done this, reinstall the paper tray and try printing again.
  4. If the printer jams again with a 241 Paper Jam error message, look to see if it has tried to feed a sheet of paper out of the tray.   
    • If paper is not leaving the tray and no paper appears to be jammed anywhere in the printer, remove paper tray 1 once again. Make sure the paper is loaded correctly in the tray. With the tray removed, you can also check the feed/pick rollers. Do the following:
      1. Look into the printer where the tray goes.
      2. Look for two tan-colored rubber rollers (circled in green in the picture below). These are the rollers that grab and feed the paper up into the printer.



         
      3. Clean off the rollers with a dry cloth and try printing again.
      4. If the printer still will not pull any paper, your feed rollers may be worn. As a temporary fix, you can try flipping the rubber feed rollers inside out. Remove paper tray 1 again and carefully remove the rubber tire off each of the roller wheels. Then flip the rubber tire inside out and put it back on the wheel. 
      5. If either step 3 or 4 fixes the problem, your feed rollers are worn and will eventually need to be replaced. However, you should be able to continue to use the printer temporarily.
      6. If the paper still does not feed at all, the feed motor to tray 1 may not be feeding the paper. In this case, the printer will require service.

         
    • If paper is feeding out of the tray but getting jammed, you may be able to pinpoint the source of the problem by taking a close look at where the leading edge of the paper is stopped.  
      • If the paper is getting jammed right at tray 1, a small piece of paper may be stuck in one of the rollers at the front of the printer. Do the following:

         
      1. Remove paper tray 1.
      2. Look into the printer where the paper tray goes. Look upwards into the very front of that area. You should see a slot or guide where the paper will go once it is fed out of the tray. Towards the left-hand side, there is a set of feed rollers. A small piece of paper can get wrapped around one of the rollers here.
      3. If you see a small piece of paper stuck in one of these rollers, try to remove it.
      4. If you cannot reach it or it cannot be removed, the assistance of a service technician will probably be needed.



        Note:
          To complete steps 1-3 above, it may help to lay the printer on its side. If you do this, please use caution when lifting the printer. Remove the toner cartridge and the paper tray before setting the printer on its side. Also make sure the printer is powered off and unplug any and all cords, especially the power cord, going into the printer. Refer to the photos below for guidance on where to look into the printer for the feed rollers. The rollers are located in the area of the printer highlighted by the yellow circles.

            

         
      • If the paper is getting past the front of the printer and jamming elsewhere with a 241 Paper Jam error, do the following:
      1. Look for any obstructions at the leading edge of where the paper is jamming.
      2. If you are not able to find (and remove) any obstruction, the printer will probably need service to isolate the problem and replace the failing component.

         
  • Another way you can find out if your printer will require service for this issue is to obtain the secondary codes for the paper jam error. To do this: 
    1. As soon as you receive the 241 Paper Jam error message, press and hold the Return button.
    2. While holding down the Return button, press the Select button. Two lines of numbers will appear on the printer screen. These are the secondary codes.
    3. If the top line of the secondary code is 8E XX 06 X1 (where X can be any letter or number), the problem could be with the pick motor for tray 1. This will probably result in the printer needing service.
  • If you continue to receive the jamming error after checking all of these possibilities, the printer may require service.
Read More..

Message Error call service 7980 on Kyocera printers






Cause

  •  Waste toner tank overflow
  • If the bottle is not full then the sensor thinks it is


Solution:

  • Clean the sensor
  • Replace waste toner tank
Read More..

Fixing error code 0xb9000009165, 0xb9000009 on HP printers



Message looks like:

Error 0xb9000009 165hw interrupt hwv2.c is
Problem with the HP printer

Solution 1:



- Uninstall all the HP drives and software
- Unplugg the USB cable from the printer
- Unplugged power supply from the outlet and printer
- Plugg the USB back in to printer

- Unplugg the power supply from the power module.
- Plugg the power supply cord to module
- Plugg the power supply in to outlet
- Plug the power module connector to printer.



Solution 2:
- Unplugg the power and usb cable from the printer
- Download and install the lastest drivers and software for the printer
- Plugg the power and then the USB.
Read More..

Pinter Xerox Phaser 750 error codes list





Error 01:
Remove and re-install the black Toner Cartridge, then turn the printer off and on.
Replace the black Toner Cartridge, then turn the printer off and on.

Error 02:

  • Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
  • Replace the cyan Toner Cartridge, then turn the printer off and on.


Error 03:
  • Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
  • Replace the magenta Toner Cartridge, then turn the printer off and on.

Error 04:
  • Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
  • Replace the yellow Toner Cartridge, then turn the printer off and on.
Error 05, 10, 11, 12, and 13:
  • Turn the printer power off, then on.

Error 20:
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Remove and re-install the Main Charge Grid. Turn the printer off, then on.
  • Remove and re-install the Transfer Kit. Turn the printer off, then on.
  • Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
  • Replace the Main Charge Grid. Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Transfer Kit. Turn the printer off, then on.
  • Replace the Toner Cartridges. Turn the printer off, then on.

Error 21, 22, 30, and 32:
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.
Error 33:
  • Check for jammed paper throughout the paper path (especially in paper feeder).
  • Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.
Error 40, 41, 42, and 43:
Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
  • Make sure that you have the correct Fuser for your local printer power supply:

    • 110-Volt Fuser Part Number 016-1839-00
    • 220-Volt Fuser Part Number 016-1840-00
  • Replace the Fuser. Turn the printer off, then on.
Error 50, 51:
Turn the printer off, then on.
Error 52:
  • Remove the Duplex Unit (if installed).
  • Check for paper under the Upper Tray.
  • Turn power off, then on.
Error 53:
  • Open left door and remove any jammed media.
  • Tun the printer off, then on.
Error 60:
  • Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
  • Reinstall the media. Make sure you do not overfill the tray.
Error 61:
  • Remove and re-install each Toner Cartridge. Turn the printer off, then on.
  • Replace each Toner Cartridge. Turn the printer off, then on.
Error 62:
  • Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).

  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Slide out and re-insert the paper feeder. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.
Error 63:
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 70, 71, and 72:
  • Turn the printer off, then on.
Error 73:
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 74:
  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.


Error 80, 81, 82, 83, and 84:
  • Make sure that all four toner cartridges are installed in the printer.
  • Turn the printer off, then on.


Error 01p through Error 47p:
  • Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
Read More..

How to solve error C000 on Canon Pixma MX870



How to solve error C000 on Canon Pixma MX870

Solution 1:



  1. Switch off the printer
  2. Disconnect the power cable
  3. Open door:







  4. Remove the orange protective tape (A) and remove the white polystyrene (protective equipment) (B).







  5. Verify in the printer there is no protective equipment:





  6. Close the door.
  7. Connect the cable and switch on.


Solution 2 :
- Check for any foreign body in the printer: piece of paper, paper clip...
- Check for any paper jams.

Solution 3:
- This error code C000 could be made by an empty cartridge: check for this.
Read More..

Unable to clean 46" error message on Brothers printers



Solution 1:
  • Pull out the AC plug.
  • Put back the AC plug while holding down the "Menu" button and keep holding it (15 sec): you're entering the Maintenance mode and "error 46" pops up in the display.
  • Select 8 by using the arrow buttons, push "OK" and select "0" and push "OK"
  • Message 00:00 00:01 OK appears.
  • Push the "Mono" button 25 times until you see PURGE: xxxxx
  • Select 2, push ok, select 7,push ok,select 8,push ok, select 3,push ok
  • Purge counter indicates: purge: 00000
  • Switch off the printer, switch it on.
Solution 2: reset the ink counter
  • Press buttons OK, Menu, Mono Start one by one, followed by up arrow key four times. this should all be done as short a time as possible, around 3 seconds.
  • Enter maintenance mode 80,  by pressing the up/down arrow key and set key to select numbers 8 and 0
  • Press blue MONO start button to select PURGE which requires it to be pressed a number of times before PURGE appears on the LCD screen of the printer
  • Use the up'down key and OK button to enter the reset code 2, 7, 8 and 3 keys to reset the counter.
    Press Stop/Exit key to go to root of maintenance mode.
  • Enter 9,9 to exit maintenance mode
Read More..

How to reset waste ink pad on Brother DCP 770CW



How to reset waste ink pad on Brother DCP 770CW

Solution for "Error 46 Unable to Clean":

  • Enter machine maintenance mode. FAX models with numerical keypads: Press the Menu/Set, *, 2, 8, 6 and 4 keys within two seconds. (if you fail to complete the correct key sequence within two seconds, press the Stop key to try again).Other (non-FAX) models: Press the Menu/Set and Black Start keys. Next press the “up arrow” key four times to enter the maintenance mode).
  • Press the 8 then 0 keys in the initial stage of the maintenance mode to call up the machine’s log information list (function code 80).
  • Press the Black Start key several times to scroll through the log information list to reach the purge counter. The purge counter is the 25th item in the list.
  • Press the 2, 7, 8, and 3 keys in this order to reset the purge count to zero.
  • Press the Stop/Exit key to return to the initial stage of the maintenance mode.
  • Press the 9 key twice to return to the standby state.
Read More..

Minolta 1080 error code list



Minolta 1080 error code list
C000 Main drive problem
C001 Main drive speed. Too fast or too slow
C004C Fan motor problem
C004E Power supply fan problem
C0070 Toner motor drive problem
C0071 Toner motor speed. Too fast or too slow
C010 Drum motor drive problem
C011 Drum motor speed. Too fast or too slow
C0400 Exposure lamp does not turn on or AE sensor problem
C0500 Low fuser temperature during warm-up
C0510 Low fuser temperature after warm-up
C0520 High fuser temperature
C0600 Scan motor drive problem
C0610 Lens motor drive problem
C0620 Mirror motor drive problem
C0990, C0991 Main tray up problem
C0992, C0993 Main tray down problem
C0994 Elevator motor problem
C0996 Main tray shift problem
C0998 Tray shift problem
C0999 Tray shift return problem
C099A, C099b Shift home problem
C099c Shift drive motor
C0b10 Auto exposure sensor problem
C0b11 Paper clamp motor
C0b30 Paper aligning motor
C0b31 Paper aligning motor
C0b50 Stapler motor
C0b51 Stapler problem
C0b52 Stapler sensor
C0b60 Sorter bin motor
C0b61-C0b64 Sorter bin movement
C0d00 Duplex rail sensor sensor problems
C0d20 Duplex home sensor
C0d50 Duplex drive motor problem
C0d51 Duplex drive motor speed
C0F10 Auto exposure sensor problem
C0F30 Paper aligning motor
C4100 Exposure lamp stays on
C0F79 Paper empty sensor problem
Read More..

Fixing error E004 on canon IR1600





Solution:Wiring

Is the connection of the connector (CN8) on the power supply PCB and the connector (J103) on the DC controller PCB and the wiring to the fixing assembly normal?
NO : Correct the connection and wiring.




Fixing assembly
Try replacing the fixing assembly.

Power supply PCB, DC controller PCB
Try repacking the power supply PCB. Is the fault corrected?
YES : End.
NO : Replace the DC controller PCB.

Error

With the power switch ON, clear E000 through E004; then, turn off and then on the power switch.
Read More..

Monday, July 2, 2012

epson CX7300, CX8300 and CX9300F Reset

epson CX7300, CX8300 and CX9300F ResetReset blow ink pad sideboard epson CX7300, CX8300 and CX9300F use improvement performance. I mortal proven this software and this software excavation. To run this software without occurrence satisfy arise the tutorial under. I know varied the bat enter and I difference the identify comrade.bat to assist when flying info fitting.
Here How to use this software :

* Download the standardisation program (see under)
* Extrak improvement you score downloaded
* Go to The extrakted folder then clink day.bat file
* Now set the associate surround in you PC to 11 Apr 2008,
* Run registration schedule by stop AdjProg.exe file the clack endure
* Penetrate Component adjustment mode then superior goal and machine porthole then utter OK
* Select Act ink pad negative from the below window and double-click to implement it
* Depression [Inactiveness] secure to stoppage current indorsement counter's continuance
* Then Clink [Initialization] to reset the infliction tabulator to the initial reckon. Thats all
* After culmination, you can replace the see to natural

Unite Accommodation document for epson CX7300, CX8300 and CX9300F
Read More..

Google Cloud Print Beta Is Limited but Evolving

The Google Cloud Print service promises to make Web-based printing--free of driver requirements and physical connections--a reality for anyone with a Gmail account and Internet access. (HP's ePrint service launched earlier, but ePrint works only with a small group of HP printers.) We tested Google's first publicly available Cloud Print beta last week. Its capabilities are still extremely limited. Within those restrictions, however, it has proven more reliable so far than the service we saw during our first forays into HP ePrint
Read More..

Solving error 5B00 on printers Canon Pixma IP6210D and IP6220D





You need to reset waste ink counter:
Step 1. Enter Service Mode

* Plug in power cable to electric source.
* Press and hold RESUME/CANCEL button
* Press POWER button
* Release RESUME/CANCEL button
* Press RESUME/CANCEL button twice in a row
Step 2. Reset Waste Ink Counter Operation
* Press RESUME/CANCEL button 4 times in a row
* Turn of the printer and then turn on again the printer. the Ink counter has been reseted
Read More..

How to Reset ink counter on Canon MP198



A. Entering into service mode



  • Turn off the printer off is the printer power on. And remove the printer USB cable from your computer..

  • While the printer is OFF, press and hold the Start/Stop button on the some other canon printers model press Resume/Cancel button.

  • While still holding Start/Stop button or Resume/Cancel button, press and hold the POWER button.

  • When the POWER LED (green light) lit, release the Start/Stop or resume/cancel button (still holding the POWER button).

  • Still holding the power button,   Press the Start/Stop button or resume/cancel button TWICE then Release the POWER button. Wait until LCD printer to display 0 (zero) number

  • After the display is 0, attach the printer UDB cable to your computer, its will detected new device installed (its normal), now go to resetting steps
B. Resetting Ink counter on the Printer

  • Run “service_tool 1050.exe”. you can download the service tool software from this link: ServiceTool_1050.zip 
  • Confirm detected USB-port numbers on USB port column.

  • Click “Main button” on Clear ink counter section. Make sure there are papers in the paper feed because the printer will print after the process is complete.

  • Click “platen button” on the “Clear ink counter” section. The printer will print again.

  • Turn off the printer and then turn the printer on.


This work too with:  MP258, MP276, MP496, MP558, MP568, and MP648

Read More..

Hi-Speed 7 Port USB 2.0 Hub +Power AC Adapter for PC

Product Description



This 7 port USB hub should be the easiest and fastest way to connect all your USB devices to PC, laptops. 7 high-speed ports can connect to an almost limitless number of USB devices including modems, scanners, printers, PC cameras, digital cameras, keyboards.Specially designed for space-saving function and multi-connection convenience. Each port handles up to 480Mbps; these devices are fully hot-swappable and daisy-chainable up to 127 devices. The LEDs help color-code your USB devices and ports. Plug this hub into just one of your computers USB ports and you'll add 7 extra USB ports to your computer. This USB 2.0 7-port hub gives you more flexibility of connections. It comes with an AC power adapter so you can run devices like external drives, printers.



Product Details

* Brand: HDE

Features



* USB 2.0 and USB 1.1 compliant and USB-IF certified. Supported data speed: 1.5/12/480 Mbps. One upstr* 8 luminescent LED lights. USB Powered. Over-current detection and protection for each downstream por* Hot-swappable plug & play connection. Daisy-chain connection of up to 127 devices. Dimensions: 100 x* Work with Windows 98/NT/2000/ME/XP. Package content: 1 x hi-speed 7-port hub with led lights, 1 x US




Read More..

Installing the Perforation Cutter and the Receipt bac on DFX-9000



  1. Unpack the Receipt bac and the Perforation cutter from the carton box.


  2. Take out the protective material from the perforation cutter.

  3.  
  4. Turn the cover forwards 1. Unscrews the two screws on the left side 2 and right side 3, which maintains the paper guide

    1 2
    3

  5. Open the Rear Unit and remove the Paper Guide.



     

  6. Caution: The perforation cutter is heavy; handle with care and use the handle
  7. Install the Perforation Cutter in the specific emplacements in each side 4 & 5.





    4 5


    Ensure each shaft of each side is correctly inserted in the housings



     

  8. Connect the I/F cable in the connector in the left side (from back side).




  9. Close the Cover Rear






  10. Insert the Supports for the receipt bac into the holes of the perforation cutter on each side.






  11. Hang the receipt bac on the support




  12. Final configuration



Read More..